Wintouch
Back to insights
Uncategorized
Published
Reading time
11 min read

Solar E-Paper Bus Stop Display: Off-Grid Sizing Checklist

Solar e-paper bus stop display sizing checklist: power budget, worst-month irradiance, battery, refresh policy and acceptance tests before you commit.

By Wintouch Engineering Team
Solar E-Paper Bus Stop Display: Off-Grid Sizing Checklist
On this page

A solar e-paper bus stop display is viable off-grid when the worst-month daily energy harvest at the exact site exceeds the daily load with a stated margin. The load is not a panel wattage: it is refreshes per day × energy per refresh, plus controller, modem and watchdog standby over 24 hours, plus any front light or heater. If the vendor cannot show that arithmetic using your five site inputs, the design is unverified — no matter how good the brochure is.

This page is deliberately an engineering counterweight to category marketing. It will not quote an autonomy figure, a cycle count or a sun-hour value for your street, because those depend on data only you can supply and only the supplier can contractually guarantee. What it gives you is the budget structure, the worst-month rule, the battery and enclosure questions that expose weak designs, and an acceptance list you can put into the award schedule.

The five numbers that decide whether solar e-paper works at this stop

Bring these five inputs to every vendor conversation. Any shortlisted design that cannot be re-run with them is a proposal, not a design.

  1. Refreshes per screen per day, split by mode — full refresh, partial refresh, fast refresh.
  2. Worst-month daily peak sun hours at the exact coordinates and tilt, from a named public dataset, not an annual average.
  3. Controller, modem and watchdog standby draw in watts, measured on the delivered configuration.
  4. Usable battery capacity at the coldest expected night temperature, after depth-of-discharge limits and low-temperature derating.
  5. Enclosure internal-to-ambient temperature delta under summer irradiance, since it caps both panel and battery ratings.

The most common mis-spec is quiet and expensive: a vendor sizes the array with annual-average irradiance, or transfers a continuous-power figure from an LCD product page onto an e-paper system. Both pass on paper in June and fail in December. Ask directly which irradiance month was used and whether the load model is duty-cycled or continuous.

Build the power budget refresh-by-refresh, not from an LCD datasheet

Write the daily load as an equation before you look at a single panel:

Term Expression Where buyers get it wrong
Full-refresh energy full refreshes/day × Wh per full refresh Using a catalogue "typical" value instead of a measured one
Partial-refresh energy partial refreshes/day × Wh per partial refresh Assuming partial refresh is free, or ignoring ghosting limits
Standby load standby watts × 24 h Omitting modem wake cycles, watchdog and front light
Daily load (Wh) sum of the three terms above Quoting panel wattage as if it were consumption

E-paper is a duty-cycled load. Energy is drawn when the panel refreshes and when the controller wakes; between updates the image holds at essentially zero power. That is why sizing an off-grid stop depends far more on content policy than on screen diagonal. A 13-inch panel updating every minute can out-consume a 32-inch panel updating every ten.

Then audit the always-on household. A cellular modem waking on a schedule, a watchdog, a front light left on through the night, or a heater for cold-morning operation will often dominate the budget. Ask for each of these as a separate line, not folded into an "average consumption" figure, and ask for the same lines restated at the coldest specified operating temperature — refresh energy and battery internal resistance both shift with temperature, and the shift is exactly what winter tests.

Winter and cloudy-week sizing: use the worst month, never the annual average

Pull monthly irradiation for the site coordinates from a named public dataset — PVGIS for Europe and many other regions, NASA POWER as a cross-check — and size against the lowest month. Derate the array with stated factors for panel soiling, tilt away from optimum, shade cast by the shelter roof or street furniture, and cable and charge-controller losses. Each factor should appear as a number in the vendor's calculation, with its source.

This page will not quote sun-hour figures. They are latitude-, season-, tilt- and shading-specific, and any published average would be wrong for your pavement.

Define autonomy in the contract rather than in conversation: how many consecutive no-harvest days the stop must run before entering a defined degraded mode. Then define what degraded mode looks like to a passenger. A stale live ETA is worse than a clean static timetable, so the fallback must be a designed content state — static schedule, service notice, reduced refresh rate — not a black screen and not a frozen countdown.

Battery selection: cycle life, cold capacity, cut-off voltage and BMS

  • Cycle life at your depth of discharge. A cycle count quoted at 80% DoD does not describe a pack run at 30% DoD. Ask for the durability figure at the DoD the design actually uses.
  • Low-temperature behaviour as a shortlist filter. Request the discharge capacity curve down to the coldest specified night and the charging cut-off temperature. Confirm the BMS blocks charging below the cell maker's limit; charging a cold lithium pack risks plating damage that shows up as lost capacity in year two.
  • Low-voltage disconnect, stated. Specify the cut-off and the state the stop enters at that point. An unintended deep discharge is a call-out, not a wear item.
  • Thermal placement. The battery compartment should be shaded and thermally separated from the panel and from direct sun on the enclosure skin. State the internal temperature range you expect the BMS to see in the hottest month and require the pack to be rated for it.
  • Field replacement. Ask whether the pack is replaceable with standard tools, and get the spare-part availability commitment and lead time in writing. Ten-year operating cost is decided here, not in the panel datasheet.

Refresh policy vs content staleness: real-time ETA and a static map are different power models

Split the content before sizing anything: real-time arrival predictions; scheduled timetable; static route map and service notices; accessibility and wayfinding. Minute-level ETA refresh can multiply daily energy by an order of magnitude compared with a five-minute or event-triggered policy.

Where the site is energy-constrained, the defensible answer is a hybrid: partial refresh of the ETA field with a slower full refresh of the surrounding layout, or an e-paper panel carrying timetable and route content while real-time data is reserved for stops whose budget demonstrably supports it. If you are weighing e-paper against LCD alternatives for the same stop, our e-paper signage vs LCD electronic shelf label buyer guide covers the panel-level trade-offs that sit underneath this budget.

Two things to require: remote configurability of the refresh interval and fallback rules, so policy can be tightened in winter without a site visit; and a table of refresh modes — full, partial, fast — with energy per operation and the visual artefact each produces. Ghosting after repeated partial refreshes is an acceptance item, not a footnote.

After dark and in low sun: front light, contrast, anti-glare and viewing angle

E-paper is reflective. Night-time legibility comes from a front light or from shelter lighting, never from the panel itself, and that light is a line in the power budget. Ask for the delivered illuminance, its energy cost, and whether it can be dimmed or scheduled.

Specify contrast ratio and viewing angle at the specified front-light level, and require a sample viewed at the real mounting height and angle, in direct sun, in overcast and at night. For a south-facing stop, the anti-reflective surface treatment matters more than any brightness number; request the treatment type and a photograph of the same content under direct sun. Check character height and font weight at the actual viewing distance against the accessibility guidance that applies in your market.

Third-party research describes sunlight readability as a category advantage of e-paper (Growth Market Reports, smart E-Ink bus stop display report; method not disclosed in the public excerpt). Treat that as category context, not a measurement of any specific panel you are buying.

Enclosure and structure: IP rating, condensation, thermal load, theft and wind

Define IP by function. Under IEC 60529, the first digit of an IP code describes protection against solid objects and the second against water. Neither digit describes condensation, which is a pressure, humidity and temperature-cycle problem. "IP65" on a marketing page is therefore not an answer to the failure mode most likely to kill an off-grid stop.

  • Condensation: ask for a pressure-equalisation breather vent or membrane, the desiccant or maintenance regime if used, and how the design handles a cold night after a humid day.
  • Thermal: a sealed enclosure in direct sun runs well above ambient. Require the internal temperature rise at a stated irradiance, logged rather than assumed, and confirm panel and battery ratings cover it.
  • Physical security: tamper-resistant fasteners, lockable service access, and a stated plan for the theft and vandalism level of the specific corridor.
  • Wind and structure: wind load on a roof- or shelter-mounted array and its bracket is a structural calculation, not a display specification. Require the mounting design signed off against the local wind-load code for the actual shelter.

Stops that add a powered interactive element — typically at interchanges where a feed exists for other reasons — move into a different component class; the 10.1" industrial touch monitor is the kind of module specified there, and it should be budgeted separately from the off-grid e-paper system rather than folded into its energy model.

Comms and remote O&M: make the stop diagnosable without a van

Require telemetry, not merely connectivity: battery state of charge, panel harvest, refresh counter, modem signal strength, internal temperature and fault codes pushed into the operator's system. Choose the radio by measured coverage reality at the stop — LTE-M or NB-IoT where those networks are dependable, LTE where they are not — and ask for signal measurements at comparable installed locations rather than a carrier coverage map.

Push for an open integration path: an API or standard protocol to the transit management or CAD/AVM system, so content ownership does not end up with the display vendor. And define the comms-outage behaviour: the stop must keep serving cached content on schedule, reconcile on reconnect, and raise an alert threshold before the battery reaches low-voltage disconnect. Cost note: the sizing exercise and the O&M contract are one decision. A smaller, correctly sized system with real telemetry usually beats a larger battery plus annual site visits.

Acceptance checklist: what to test before you sign

  1. Factory energy record. Energy per refresh and standby draw measured on the delivered configuration at the specified cold and hot temperature points, with a signed test record.
  2. Autonomy re-calculation. Worst-month energy balance rebuilt from those test records plus the site dataset, run against the contracted autonomy days and the defined degraded mode.
  3. Optical test. Real content read at mounting height in direct sun, overcast and at night, including front-light level and ghosting after a defined number of partial refreshes.
  4. Environmental and physical test. IP verification method stated, breather vent confirmed present, internal temperature logged over a full diurnal cycle in sun, tamper hardware inspected.
  5. Handover test. Telemetry visible in the operator's dashboard, refresh policy changeable remotely, firmware update path documented, and spare battery, panel and controller part numbers with lead times in writing.

Where published market data ends and your site data must begin

Directional context only: one research publisher puts Asia Pacific at roughly 42.3% of the global ePaper bus stop display market in 2025 (Marketintelo, 14 August 2025, marketintelo.com/report/epaper-bus-stop-display-market), while another estimates APAC revenue for solar-powered e-paper bus stops near USD 547 million in 2025 (Growth Market Reports, publication date not verified in the public excerpt). Neither excerpt discloses its method, sample or segment definitions, so use these to sanity-check a business case and a procurement timeline — not a design.

Three local inputs override any published figure: the site irradiance dataset for your coordinates and tilt, the operator's actual content refresh policy, and the corridor's lighting and vandalism environment. Those three determine whether your shaded, north-facing stop still shows the correct departure in February.

Frequently asked at shortlist stage

How many refreshes per day can an off-grid e-paper stop sustain?

There is no universal number — it falls out of the budget. Divide the worst-month daily harvest, after derating, by the measured energy per refresh plus the 24-hour standby load. That quotient, not a vendor headline, is your refresh allowance.

Can it survive a week of cloudy winter days?

Only if autonomy days are contracted and the degraded mode is designed. Ask for the consecutive no-harvest days guaranteed, the test that proves it, and the content state the stop enters when the reserve is depleted.

Is solar cheaper than trenching a power connection?

Compare total cost over the service life: trenching, connection and metered power against array, battery replacement intervals, enclosure thermal design and site visits. Your own civils quote and the supplier's battery replacement schedule are the two inputs that decide it.

What IP rating and vent does an off-grid enclosure need?

Set the IP digits against the actual dust and water exposure, then resolve condensation separately with a breather membrane and a maintenance regime. IEC 60529 defines the digits; it does not certify condensation performance.

How readable is e-paper at night with no shelter lighting?

Only as readable as its front light makes it. Require delivered illuminance, the energy it adds to the budget, dimming or scheduling control, and a night-time sample at the real mounting height.

Get the sizing worksheet and a real datasheet, not a brochure

Request the off-grid sizing worksheet plus site-survey checklist, and the display/controller datasheet with per-refresh energy and standby figures stated at defined temperatures. Send your site coordinates, number of screens, content refresh policy, and coldest and hottest expected temperatures with the request, so the first reply is a calculation you can audit rather than a sales call.

Ask in the same message for the solar / off-grid e-paper bus stop display system configuration page covering enclosure, structure and controller options — that is where the budget above becomes a specified bill of materials. If the supplier cannot return your five inputs filled in, keep them on the shortlist only until someone else does.

About the author

Wintouch Engineering Team

Our commercial-display engineers and product team review specifications against current factory records, deployment requirements and published standards. Learn more about our engineering capability and manufacturing operation.

Continue researching

Product facts and engineering claims follow our data and editorial policy.

Have a deployment question?

Share your environment, screen size and integration requirements with our engineering team.